Ethernet Topology MCQ Questions with Answers

Ethernet Topology MCQ Questions and Answer| Solved Multiple Choice Questions and Answer on Ethernet Topology

Ethernet Topology MCQ Quiz: The Ethernet is most widely used in Network topology and uses the carrier sense multiple access with collision detection (CSMA /CD). The Ethernet connection provides faster speed, more reliable and more secure than WIFI is are the advantages of Ethernet. In this section, we have to discuss about multiple choice questions and answers on Ethernet Topology are given below. You have read the given networking/Ethernet topology mcq questions clearly. This is the great opportunity for candidates learning Ethernet topology/networking topology questions etc. Click here to download the below links. This below quiz is helpful for candidate preparing various government exams etc.

Click here for Web Technology MCQ Questions

General Knowledge Questions and Answer for Bank Exams

Click here for Computer Networking MCQ Questions

Ethernet Topology MCQ Questions

1. The Frame Check Sequence (FCS) of an Ethernet Frame is a _______ code.

1. End of Frame
2. Cyclic Redundancy Check
3. Cyclic Error Check
4. Beginning of Frame

Answer: Cyclic Redundancy Check

2. Which is the network topology that is prone to bottlenecks though easy to install?

1. STAR
2. RING
3. BUS
4. TREE

Answer: STAR

3. What is the sped of a 100BaseT cable?

1. 10 mbps
2. 1 gbps
3. 100 mbps
4. None

Answer: 100 mbps

4. Pick the topologies used in a LAN network below.

1. RING
2. STAR, TREE
3. BUS
4. All the above

Answer: All the above

5. The number of bits used for addressing in Gigabit Ethernet is _______

1. 64 bits
2.  48 bits
3. 128 bits
4. 32 bits

Answer: 48 bits

6. In a ___ topology, all the nodes or stations are connected to a main central cable.

1. STAR
2. BUS
3. TREE
4. RING

Answer: BUS

7. What are the parts of An Ethernet Frame?

1. FCS
2. Ethernet header
3. Payload
4. All of above

Answer: All of above

8. In a ___ topology, the nodes or stations of a network are connected to a central hub or server.

1. STAR
2. BUS
3. TREE
4. RING

Answer: STAR

9. An Ethernet Jack is _________.

1. RJ14
2. RJ11
3. RJ45
4. None

Answer: RJ45

10. An Ethernet header contains ___ as the first two fields.

1. Source MAC Address
2. Destination MAC Address
3. Destination and Source MAC Addresses
4. None

Answer: Destination and Source MAC Addresses

11. In Ethernet CSMA/CD, the special bit sequence is transmitted by media access management to handle collision is called

1. Jam
2. Preamble
3. Postamble
4. None

Answer: Jam

12. Ether LAN uses_________

1. Differential Manchester encoding
2. Polar encoding
3. NRZ
4. Manchester encoding

Answer: Manchester encoding

13. Which is the highest reliability topology?

1. Star
2. Mesh
3. Ring
4. None

Answer: Mesh

14. An alternate name for the completely interconnected network topology is________

1. Ring
2. Star
3. Mesh
4. None

Answer: Mesh

15. In half duplex mode of media access control (MAC) sub layer the stations are connected through __________

1. bus
2. switch
3. hub
4. bridge

Answer: hub

16. Which of the following is an important characteristic of LAN?

1. low cost access for low bandwidth channels
2. application independent interfaces
3. unlimited expansion
4. parallel transmission

Answer: application independent interfaces

17. Ethernet belongs to which standard?

1. IEEE 802.2
2. IEEE 802.4
3. IEEE 802.3
4. IEEE 802.5

Answer: IEEE 802.3

18. An Ethernet frame that is less than the IEEE 802.3 minimum length of 64 octets is called________

1. Mini frame
2. Small frame
3. Short frame
4. Runt frame

Answer: Runt frame

19. The minimum frame length for 10-mbps Ethernet is 64 bytes and the maximum is___________

1. 1520 bytes
2. 1000 bytes
3. 500 bytes
4. 1518 bytes

Answer: 1518 bytes

20. In networking terminology UTP means__________

1. Uniquitous teflon port
2. Uniformly terminating port
3. Unshielded twisted pair
4. Unshielded T-connector port

Answer: Unshielded T-connector port

21. A mechanism or technology used in Ethernet by which two connected devices choose common transmission parameters such as speed, duplex mode and flow control is called

1. Synchronization
2. Autonegotiation
3. Autosense
4. Pinging

Answer: Autonegotiation

22. The 10 base 5 cabling is also known as ___________

1. Thin Ethernet
2. Fast Ethernet
3. Thick Ethernet
4. Gigabit Ethernet

Answer: Thick Ethernet

23. In which of the topology, each device has a dedicated point-to-point link to a central controller?

1. Mesh
2. Ring
3. Star
4. Bus

Answer: Star

24. IEEE stands for ___

1. Institute Ethernet and Electronics Engineering
2. Institute of Electrical and Electronics Engineering
3. Institute of Electrical and Electronics Engineers
4. None

Answer: Institute of Electrical and Electronics Engineers

25. In Which topology , every node is connected to 2 other nodes?

1. Bus
2. Mesh
3. Ring
4. Star

Answer: Ring

Students to get more general knowledge quiz must watch our site regularly. candidates who are searching Ethernet Topology MCQ Questions and answers are provided above. Learn & practice lots of Ethernet topology mcq questions daily.